Product Description

READY NOW!!!!CALL FOR MORE INFO!!!! 586-991-0054

BUY NOW!!!   LOWEST PRICE EVER!!!!!

1) 2023 INTERNATIONAL MV607
-37,000 GVWR
-9L CUMMINS 300 HP
-ALLISON 3500 RDS
-SCHOOL BUS YELLOW

1) VERSALIFT VN50 AERIAL
-HEIGHT TO BOTTOM OF BUCKET 52′
-WORKING HEIGHT 57′
-TRAVEL HEIGHT 13’6″
-700LB BUCKET CAPACITY, PLATFORM @12′ RADIUS
-69 KV DIELECTRIC -REVERSE MOUNTED
-OUTRIGGERS MOUNTED DIRECTLY BEHIND CAB
-AERIAL PEDESTAL SHALL BE LOCATED IMMEDIATELY BEHIND OUTRIGGERS W/BUCKET STORED ABOVE CAB
-OPEN CENTER UNIT
-FIBERGLASS BOOM AND INSERT CONSTRUCTION. FILAMENT WOUND
-UPPER BOOM SHALL BE FIBERGLASS W/STEEL TIP AND STUB
-TWO (2) SAFETY ATTACHEMENTS SHALL BE LOCATED FOR EASE OF USE, ON TOP OF UPPER BOOM.
-LOWER BOOM SHALL HAVE A 24″ FIBERGLASS INSERT, BE MOUNTED TO TURN TABLE W/360 DEREE CONTINUOUS ROTATION, TRAVEL 15′ DEGREES PAST VERTICAL, PADDED UPPER BOOM REST, LOAD LIFTING EYE AND EYE LOAD LIFTING CHART
-UPPER BOOM HOLD DOWN: MANUAL CLAMP
-LOWER BOOM LOCK
-BOOM CYLINDERS PILOT OPERATED CHECK VALVES WITH EMERGENCY BYPASS PROVISIONS
-BUCKET 42″X1-48″X24″
-FIBERGLASS BUCKET TOTALLY ENCLOSED
-TWO (2) EXTERNAL BUCKET ACCESS STEPS WITH NO-SKID FINISH
-TWO (2) EXTERNAL ACCESSORY RINGS FOR CLIP-ON BUCKETS TO BE LOCATED BOOM SIDE OF BUCKET N EAR EACH CORNER
-BASKET LINER AND COVER
-ONE (1) DROP IN SCUFF STEP
-BASKET SHALL BE END MOUNTED, ABLE TO ROTATE 90 DEGREES FROM CENTER BOTH LEFT AND RIGHT
-FALL ARREST SYSTEM INCLUDES ONE LARGE BODY HANRESS AND DECELERATING LANYARD
OUTRIGGERS:
-TWO (2) OUTRIGGERS
-DASH MOUNTED RED WARNING LIGHT INDICATING LOWERED OUTRIGGER
-CONTROLS LOCATED UNDERNEATH LEFT SIDE AND RIGHT SIDE OF REAR PLATFORM
-AUDIBLE ALARM WHEN OUTRIGGERS EXTENDING
-TWO (2) ADJUSTABLE OUTRIGGER PADS ALUMINUM WITH STORAGE RACKS MOUNTED NEAR OUTRIGGERS, UNDER UTILITY BODY COMPARTMENTS
HYDRAULIC SYSTEM:
-CHELSEA HOT SHIFT PTO WITH CONTROL SWITH, INDICATOR LIGHT AND PTO HOUR METER.
-NEUTRAL INTERLOCK/SHIFT INHIBITOR WHILE PTO IS ENGAGED
-HYDRAULIC PUMP, ARRANGMENT: 3 SECTION (WINCH/GENERATOR/AERIAL) PUMP UTILIZING A COMMON OIL SUPPLY
-HYDRAULIC PUMP, WINCH: VANE PUMP TO PROVIDE 25GPM@2500 PSI@ ELEVATED IDLE
-HYDRUALIC PUMP, GENERATOR: VANE PUMP TO PROVIDE 8GPM@2000PSI@ELEVATED IDLE
-HYDRAULIC PUMP, AERIAL: PRESSURE COMPENSATED, VARIABLE VOLUME HYDRAULIC PUMP PROVIDING 17GPM@ 2000 PSI. OPEN CENTER HYDRAULIC SYSTEM
-GENERATOR AND WINCH OPERATIONS WILL NOT AFFECT PERFORMANCE OF AERIAL
-HYDRAULIC FITTINGS STEEL AND HIGH PRESSURE
-37 DEGREE JIC FITTINGS UTILIZED WHERE POSSIBLE
-TOOL LINE SHUT-OFF VALVE AT PLATFORM
-FITTINGS FOR ONE TOOL AND SHUT OFF VALVE AT THE BASE OF UNIT
-TOOL COUPLINGS GREENLEE HTMA DRIPLESS AND FLUSH MATING SURFACE
-INSULATED TOOL LINES
CONTROLS, UPPER:
-TRUGUARD DIELECTRIC ISOLATING SYSTEM WITH RIGHT HAND SINGLE STICK CONTROL. ALL CONTROL HANDLES ARE ISOLATED AND TESTED PER ANSI92.2.2009. THE HIGH RESISTIVE DIELECRIC SYSTEM IS PROTECTED FROM DIRECT ENVIRONMENTAL
AND JOB-RELATED CONTAMINATION.
-A SINGLE HANDLE STYLE CONTROL (TO CONTROL UPPER BOOM RAISE/LOWER, EXTEND/RETRACT AND TOWER ROTATION.
-UPPER BOOM CONTROL CAPABLE OF 3 SIMULTANEUOUS MOVEMENTS.
-SAFETY INTERLOCK
-ENGINE START/STOP
-HIGH REV SWITCH INTEGRATED INTO HANDLE GRIP CONTROLS, LOWER:
-PEDESTAL MOUNTED CONTROLS FOR ALL BOOM/BASKET FUNCTIONS WITH SAFETY GUARD
-LOWER BOOM CONTROLS CONVENTIONAL LEVER TYPE
-LOWER CONTROLS CAPABLE OF OVER-RIDING THE PLATFORM CONTROLS EVEN IF UPPER CONTROLS ARE DAMAGED OR SEVERED.
-TOOL CIRCUIT SHUT OFF
-SAFETY INTERLOCK CONTROL
EMERGENCY LETDOWN SYSTEM:
-12 VOLT EMERGENCY HYDRAULIC SYSTEM
BASKET LEVELING:
-PLATFORM LEVELING
WINCH,FRONT, BUMPER MOUNTED:
-BRADEN FRONT FRAME MOUNTED ASSEMBLY WITH HEAVY DUTY BUMPER AND CURBSIDE EXTENDED SHAFT
-SINGLE SPEED HYDRAULIC MOTOR
-1ST LAYER LINE PULL CAPACITY (MIN)20,000LB IN LOW SPEED/HIGH TORQUE MODE
-500′ OF SUITABLE 7/16″ CABLE WITH “S” HOOK
-4 WAY GUIDE ROLLER AND TENSION ROLLER
-HI/LOW SPEED SELECTRO VALVE
-SUITABLE OPERATOR CONTROLS FOR SPOOL ENGAGE/DISENGAGE AND CABLE IN/OUT WITH 10′ CORD FOR REMOTE CONTROL BOX
-STANDARD LEVEL OPERATED HYDRAULIC CONTROLS
-EXTENDED FRONT BUMPER AREA COVERED WITH TREAD PLATE
CAB GUARD:
-FULL CAB CONSTRUCTED OF 1-1/2″ STANDARD EXPANDED METAL ON 2″ STANDARD PIPE STANCHIONS W/MOUNTING LADDER AND HAND RAIL TO BASKET
PEDESTAL:
-HIGH STRENGTH STEEL PEDESTAL WITH ACCESS HOLES FOR MAINTNANCE/REPAIR
-SELF LOCKING WORM GEAR ROTATION DRIVE WITH BI-DIRECTIONAL MOTOR
-A 7/8″ EXTERNAL HEX SHAFT
INVERTER:
-GP-3000HD CONTINUOUS POWER INVERTER (MODIFIED SINE WAVE)
-SURGE POWER CAPABILITY (PEAK POWER) 6000 WATTS
-QUAD AC RECEPTACLE
-USB OUTPUT 4.75-5.25 VDC/2.1A
-DC INPUT/OPERATING VOLTAGE 10.5 TO 16 VOLTS
-OUTPUT VOLTAGE: 100-120 VAC RMS +5/-15
-BATTERY LOW VOLTAGE ALARM: 10.5V +/-0.5 VOLTS
-BATTERY LOW VOLTAGE SHUTDOWN: 10.0 +/-0.5 VOLTS
-FULL LOAD EFFICIENY 85% -1/3 LOAD EFFICIENCY 90%
-AC OUTPUT SOCKET TYPE: DUAL TYPE 2-3 PRONG
-INDICATOR LIGHT IN CAB WHEN INVERTER IS ON
-ON/OFF SWITCH IN CAB
-THREE (3) GFI PROTECTED 120-VAC, 15 AMP OUTLETS IN WEATHER PROOF BOXES ONE LOCATED AT CURBSIDE REAR BODY, AND ONE LOCATED NEAR CONTROL PANEL INSIDE #3 CABINET, ONE MOUNTED INSIDE CAB.
-120-VAC WIRING
1) UTILITY BODY BRANDFX
-GEL COAT TO MATCH CAB
-HEAVY DUTY SHELVING
CURBSIDE COMPARTMENTS:
-VERTICAL: 27″W X 48″H WITH FOUR ADJUSATBLE SHELVES WITH REMOVABLE DIVIDERS
-OPEN WITH TWO CARGO AREA ACCESS STEPS
-VERTICAL: 27″W X 48″H WITH THREE ADJUSTABLE SHELVES. INVERTER INSTALLED WITH REMOVABLE SHELF ABOVE
-HORIZONTAL 54″W X 18″H ONE SHELF WITH A CENTER SUPPORT WITH TWO 4 DRAWER PACKS INSTALLED BELOW.
-VERTICAL 27″W X 44″H, WITH NINE MATERIAL HOOKS
STREETSIDE COMPARTMENTS:
-VERTICAL: 27″W X 48″H WITH FOUR ADJUSTABLE SHELVES
-VERTICAL: 27″W X 48″H WITH NINE MATERIAL HOOKS, THREE ON EACH SIDE
-VERTICAL: 27″W X 48″H WITH THREE ADJUSTABLE SHELVES
-HORIZONTAL: 54″W X 18″H WITH ONE (1) SHELF WITH REMOVABLE DIVIDERS
-VERTICAL: 27″W X 48″W WITH NINE MATERIAL HOOKS
-REAR HOT STICK THRU COMPARTMENT SHELF WITH DOOR
-LED ROPE LIGHTING EACH COMPARTMENT
-LIGHT SWITCH INSIDE CAB ON THE CONTROL PANEL
-STORAGE RACKS FOR OUTRIGGER PADS MOUNTED NEAR OUTRIGGERS UNDER COMPARTMENTS
-THREE (3) EXTERNAL MOUNTED BINS, 1 ALUMINUM 7’LONG 16″ WIDE AND 12″ TALL MOUNTED ON TOP OF CAGE OVER CAB ALL THE WAY TO DRIERS SIDE EDGE DOOR OPENS ON TOP. 1 STAINLESS 36″LONG X 18″DEEP AND 18″ TALL MOUNTED ON
DRIVERS SIDE OVER UTILITY BINS DOOR OPEN TOWARD TOP. 1 STAINLESS 16″ LONG 18″ WIDE 18″ TALL MOUNTED ON PASSENGER SIDE OVER UTILITY BINS DOOR OPEN TOWARD INSIDE OF TRUCK BOX.
-ONE PIECE SOLID FIBERGLASS CONSTRUCTION W/REINFORCED LOAD FLOOR AND FRONT DASH.
-ALL FASTENERS STAINLESS STEEL
-BOLTS ALL WITH SELF LOCKING NUTS
-DOUBLE LAMINATED DOORS WITH BUILT IN DRAINAGE
-CABLE DOOR RESTRAINTS
-DOOR SEALS: NEOPRENE AUTOMOTIVE TYPE
-DOORS PROTECTED BY A DRIP EDGE OVER DOOR
-CABLE DOOR RESTRAINTS
-ALL DOOR LOCKS KEYED ALIKE, ALL DOOR LATCHES SLAM TYPE
-FLARED WHEEL WELLS
-WHEEL WELL COVERS WITH WHEEL CHOCK STORAGE COMPARTMENT INCORPORATED
-SUITABLE LIGHTWEIGHT CHOCK BLOCKS
-ALUMINUM ROCK GUARDS INSTALLED AT LOWER FRONT CORNERS OF BODY AND REAR OF WHEEL WELLS.
-TAILGATE POCKETS SIZED TO FIT A 2X6 BOARD REAR OF CARGO AREA
-SUITABLE MUD FLAPS FOR REAR WHEELS
-STREET SIDE LADDER BRACKETS WITH LOCKING CAM
-ROPE RAIL, CARGO AREA 80″ LONG STARTING AT STREET SIDE REAR, MOUNTED ON TRUCK BOX SIDE OF UTILITY BINS
-REAR OF CABINETS WITH PROVISIONS FOR REAR TAILLIGHTS. 4″ FLUSH MOUNTED WARNING AND CLEARANCE LIGHTS
-EXTENSION NONSKID COATED
REAR PLATFORM:
-A FULL WIDTH, REINFORCED 18″ DEEP PLATFORM
-PLATFORM TOP NON SKID COATING
-FULL LENGTH TRAVERSE COMPARTMENT: APPROX 6″H X 16″W WITH A DOOR ON EACH END FOR EASY ACCESS AND CLEANOUT
-DOORS STAINLESS STEEL SLAM TYPE LATCHES AND STRIKER PLATES
-ALL DOORS KEYED ALIKE
REAR BUMPER:
-FULL WIDTH, GRIP STRUT TYPE BUMPER WITH RECESSED PINTLE HITCH PROVISION AND SAFETY CHAIN LOOPS
-BUMPERS WITH PUNCHED HOLES
-PINTLE HITCH HOLLAND PHT100
-TWO (2) 7 WIRE ROUND TRAILER PLUGS INSTALLED NEAR HITCH.
ELECTRICAL:
-MULTI SWITCH PANEL WITH INDICATOR LIGHTS LOCATED INSIDE OF CAB AND CONTROL POWER FOR PTO, SPEED UP, MOUNTED EQUIPMENT INCLUDING WARNING LIGHTS/ BEACONS.
-CONTINUOUS DUTY RELAYS
-CIRCUIT PROTECTION
-ELECTRONIC BACK UP ALARM
-BACKUP CAMERA WITH IN DASH MONITOR
LIGHTING:
-FRONT HEADLIGHTS ALERNATING FLASHER (SOUND OFF ETPPSS-P)
-ALL OUTSIDE BODY LIGHTS LED AND FLUSH RUBBER MOUNTED
-WIRING HARNESS ENCASED IN PLASTIC LOOM AND WIRES COLOR CODED
-REAR TAILLIGHTS AND WIRING PROTECTIVE METAL GUARDS INSTALLED INSIDE OF CABINETS
-LED STOP, TAIL AND TURN LIGHTS (SOUND OFF ECV42STT)
-LED AMBER SELF CONTAINED WARNING LIGHT (SOUND OFF ERDREBZA)
-BODY & CLEARANCE LIGHTS: (SOUND OFF ERDREBZA)
-FOUR (4) DUAL BEAM REVOLVING AMBER WARNING BEACONS: ONE (1) CENTER OF CAB, ONE (1) LEFT REAR AND TWO (2) REAR ON TOP OF UTILITY BODY CABINETS.
-WARNING BEACON (TARGET TECH TT-450112-AMB)
-WARNING BEACON WIRING 12 GA
-THREE SWITCHES SHALL CONTROL THE WARNING LIGHTS:
1) HEADLIGHT FLASHERS, 2) ROOF MOUNTED WARNING BEACON AND REAR LED WARNING LIGHTS, 3) REAR CABINET MOUNTED WARNING BEACONS
1) HEADLIGHT FLASHERS, 2) ROOF MOUNTED WARNING BEACON AND REAR LED
WARNING LIGHTS, 3) REAR CABINET MOUNTED WARNING BEACONS
-LICENSE LIGHT AND PLATE HOLDER REAR OF CURBSIDE CABINET
-REMOTE CONTROLLED SPOTLIGHT MOUNTED ON PASSENGER SIDE OF CAGE OVER CAB.
REMOTE SHALL BE MOUNTED INSIDE TRUCK CAB ACCESSIBLE TO DRIVER.
ACCESSORIES:
-ONE (1) EMERGENCY WARNING KIT WITH FLAG, FLARE, AND TRIANGLE KIT
-ONE (1) 5LB FIRE EXTINGUISHER W/MOUNTING BRACKET
-CHEMICAL / OIL RESISTANT SHELF MATTING IN ALL COMPARTMENTS
-LARGE BODY HARNESS
AERIAL MAINTENANCE:
-FALL ARREST SYSTEM SHAL INCLUDE (1) LARGE BODY HARNESS
-AERIAL EQUIPMENT MAINTENANCE SCHEDULE TO BE INCLUDED
-ONE SET OF OPERATOR MANUALS PER UNIT
-ONE SET OF SHOP MANUALS PER UNIT

CALL FOR SPECIAL PRICING!!!!